DETERMINATION OF THE BENDING STIFFNESS OF THIN-WALLED SHAFTS BY THE EXPERIMENTAL METHODOLOGICAL METHOD DUE TO THE FORMATION OF INTERNAL STRESSES

Abstract View PDF Download PDF

##plugins.themes.academic_pro.article.sidebar##

Published May 16, 2021
https://doi.org/10.17605/OSF.IO/KFSR6
Download
PDF
Statistic

Downloads

Download data is not yet available.
Vol. 6 No. 2 (2021): VOLUME 6 ISSUE 2

##plugins.themes.academic_pro.article.main##

Sh. Fayzimatov
P.G. Doctor of technical sciences, professor Department of “Mechanical engineering and automatization”, Fergana Polytechnic Institute, Fergana, Uzbekistan
Sh. Rubidinov
Assistant of the Department of Mechanical Engineering and Automation, Fergana Polytechnic Institute, Fergana, Uzbekistan

Abstract

This article presents the results of computer simulation of the flexural stiffness of thin-walled shafts. Influence of residual stresses on the maximum bending value of shaft-type parts. During the experimental and methodological work, it was found that the formation of residual stresses in the surface layers of a certain thickness have a positive effect on increasing the stiffness of the shafts. The results obtained make it possible to explain a number of experiments on the hardening of shafts by surface plastic deformation. Determination of the bending stiffness of low-stiff shafts due to the formation of residual stresses is allowed only when it is possible to create deeper fields of their distribution.

##plugins.themes.academic_pro.article.details##

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

How to Cite
[1]
Sh. Fayzimatov and Sh. Rubidinov, “DETERMINATION OF THE BENDING STIFFNESS OF THIN-WALLED SHAFTS BY THE EXPERIMENTAL METHODOLOGICAL METHOD DUE TO THE FORMATION OF INTERNAL STRESSES”, IEJRD - International Multidisciplinary Journal, vol. 6, no. 2, p. 5, May 2021.
Crossref
Scopus
Google Scholar
Europe PMC

References

  1. Nomanjonov, S., et al. "STAMP DESIGN." Экономика и социум 12 (2019): 101-104.
  2. Юсуфжонов, О. Ғ., and Ж. Ғ. Ғайратов. "ШТАМПЛАШ ЖАРАЁНИДА ИШЧИ ЮЗАЛАРНИ ЕЙИЛИШГА БАРДОШЛИЛИГИНИ ОШИРИШДА МОЙЛАШНИ АҲАМИЯТИ." Scientific progress 1.6 (2021): 962-966.
  3. Рубидинов, Шохрух Ғайратжон Ўғли. "БИКРЛИГИ ПАСТ ВАЛЛАРГА СОВУҚ ИШЛОВ БЕРИШ УСУЛИ." Scientific progress 1.6 (2021): 413-417.
  4. Тешабоев, Анвар Эргашeвич, et al. "МАШИНАСОЗЛИКДА ЮЗА ТОЗАЛИГИНИ НАЗОРАТИНИ АВТОМАТЛАШ." Scientific progress 1.5 (2021).
  5. Nomanjonov, S. N. "Increase The Wear Resistance And Service Life Of Dyes Based On Modern Technologies." The American Journal of Engineering and Technology 2.12 (2020): 67-70.
  6. O’Lmasov Ahadjon Akramjon, O’G. "NEW APPROACHES IN THE DIAGNOSIS AND MONITORING OF ROTOR OSCILLATIONS USING SHAFT SENSORS." Science and Education 1.1 (2020).
  7. Отақулов, Ойбек Хамдамович, and Расул Каримович Таджибоев. "КОМПРЕССОР ВАЛЛАРИДАГИ САЛБИЙ ТИТРАШЛАРНИ БАРТАРАФ ЭТИШДА КИМЁВИЙ ТЕРМИК ИШЛОВ БЕРИБ ЦЕМЕНТИТЛАШ ЖАРАЁНИНИНГ МЕТОДОЛОГИЯСИ ВА АФЗАЛЛИКЛАРИ." МОЛОДОЙ ИССЛЕДОВАТЕЛЬ: ВЫЗОВЫ И ПЕРСПЕКТИВЫ. 2020.
  8. Fayzimatov, B. N., and Yu Yu Xusanov. "PROBLEMS OF GLASS SURFACE QUALITY FORMATION FOR MECHANICAL PROCESSING." Scientific-technical journal 22.2 (2018): 35-39.
  9. Файзимтов, Шухрат Нуманович, and Мухаммадазим Акбаралиевич Рустамов. "ПРИМЕНЕНИЕ ПРОГРЕССИВНЫХ МЕТОДОВ ДЛЯ ОРИЕНТАЦИИ И УСТАНОВКИ ЗАКЛЕПОК В ОТВЕРСТИЕ С ГОРИЗОНТАЛЬНОЙ ОСЬЮ." НАУЧНЫЙ ПОИСК В СОВРЕМЕННОМ МИРЕ. 2017.
  10. Файзиматов, Ш. Н., and М. А. Рустамов. "АЭРОДИНАМИЧЕСКИЙ ЭФФЕКТ ДЛЯ АВТОМАТИЗАЦИИ ПРОЦЕССА ПЕРЕКАЧКИ ХИМИЧЕСКИХ АГРЕССИВНЫХ РЕАГЕНТОВ." Современные исследования 6 (2018): 112-115.
  11. Teshabaev, Anvar, and Rakhimov Sharifjon. "The innovation activity on large uzbek companyas a key factor of personnel development." ACADEMICIA: An International Multidisciplinary Research Journal 10.5 (2020): 416-423.
  12. Turakhodjaev, Nodir, et al. "EFFECT OF METAL CRYSTALLATION PERIOD ON PRODUCT QUALITY." Theoretical & Applied Science 11 (2020): 23-31.
  13. Turaevich, Turaev Tirkash, and Madaminov Bakhrom Mirodilovich. "Physical Foundations Structural-Formation, Surface Layer Of Parts." The American Journal of Engineering and Technology 2.09 (2020): 71-76.
  14. Тураев, Тиркаш Тураевич, Якуб Анвархаджаевич Батиров, and Бобурбек Абдулҳаким Ўғли Тожиев. "Модернизация процесса волочения проволочного изделия." Universum: технические науки 3 (60) (2019).
  15. Fayzimatov, Sh N., Y. Y. Xusanov, and D. A. Valixonov. "Optimization Conditions Of Drilling Polymeric Composite Materials." The American Journal of Engineering and Technology 3.02 (2021): 22-30.
  16. Файзиматов, Шухрат Нуманович, and Шухрат Махмутжонович Абдуллаев. "ДОРНАЛАР ЁРДАМИДА КИЧИК ЎЛЧАМЛИ ЧУҚУР ТЕШИКЛАРГА ИШЛОВ БЕРИШ АНИҚЛИГИ ВА САМАРАДОРЛИГИНИ ОШИРИШ." Scientific progress 1.6 (2021): 851-856.
  17. Юсупов, Сардорбек Маъруфович, et al. "КОМПАЗИЦИОН МАТЕРИАЛЛАРНИ БОРЛАШ." Scientific progress 1.4 (2021).
  18. Todjiboyev, R. K., A. A. Ulmasov, and Muxtorov Sh. "3M structural bonding tape 9270." Science and Education 2.4 (2021): 146-149.
  19. Fayzimatov, Sh N., S. M. Yusupov, and B. I. Abdullaev. "Increasing Durability of Working Elements of Dividing Dies." International Journal of Advanced Research in Science, Engineering and Technology 7.4 (2020).
  20. Файзиматов, Шухрат Нуманович, Сардорбек Маъруфович Юсупов, and Абдужалол Дўсмухаммад Угли Бектемиров. "ИСПОЛЬЗОВАНИЕ СОВРЕМЕННЫХ ПРОГРАММНЫХ ТЕХНОЛОГИЙ ПРИ ПРОЕКТИРОВАНИИ ШТАМПОВ." Universum: технические науки 3-1 (84) (2021): 11-13.

Most read articles by the same author(s)

Obs.: This plugin requires at least one statistics/report plugin to be enabled. If your statistics plugins provide more than one metric then please also select a main metric on the admin's site settings page and/or on the journal manager's settings pages.